AS568-282

Standard Imperial O-Ring Size

Dimensions

Inside Diameter (inch)	15.955 in
Cross Section (inch)	0.139 in
Inside Diameter (mm)	405.26 mm
Cross Section (mm)	3.53 mm
Recommended Groove Depth	0.112 in
Theoretical Static Compression	19.4% (Target: 15-25%)

Quick Reference

ID: 15.955" (405.26 mm)

CS: 0.139" (3.53 mm)

Static Compression: 19.4%

Target Range: 15–25% static, 10–20% dynamic

Groove Depth: 0.112 in

Groove Width: 0.167 in (1.2× CS)

About This Size

AS568-282 is a AS568 200 Series imperial O-ring with 15.955" inside diameter (405.26 mm) and 0.139" cross section (3.53 mm). At the recommended groove depth of 0.112", theoretical static compression is 19.4% — within the typical 15–25% target for static glands. This dash number is widely stocked in NBR, FKM, EPDM, VMQ, and PTFE for heavy machinery, large cylinders, process equipment.

Part of AS568 200 Series

Adjacent Sizes

AS568-281

Smaller ID (same cross section)

AS568-283

Larger ID (same cross section)

Cross-Standard Reference

Standard	Nearest Size	ID Δ	CS Δ
ISO 3601	250.00x2.65	155.26 mm	0.88 mm
JIS B 2401	P-5.70x400.00	5.26 mm	2.17 mm

Cross-reference values are catalog nearest matches — always verify groove width, depth, and tolerance class on your drawing before substituting standards.

Compression Rate Guidance

Static seals: 15–25% compression is ideal for most fixed applications.
Dynamic seals: 10–20% compression to reduce friction and wear.
Groove width should typically be 1.1 to 1.3 times the O-ring cross section.
Surface finish: Ra 0.8–3.2 µm for static, Ra 0.4–0.8 µm for reciprocating dynamic service.

Typical Applications

Large static flange seals
At 405 mm ID, this size serves tank lids, heat exchanger covers, and large-bore pipeline flanges.
Construction & mining equipment
Common on excavator cylinders, crusher housings, and other high-load static joints with generous gland geometry.

Tolerance & Standard Notes

AS568 defines a single tolerance table that applies to every dash number (the two-class system of the 1971 issue was merged in AS568A). For critical dynamic seals, tighter-than-standard dimensional tolerances agreed with the manufacturer (per drawing) are the standard route; surface quality is specified separately under ISO 3601-3 grades N, S, or CS.

For tolerance details, see the O-Ring Tolerance Guide.

Design FAQ

What AS568 series is dash 282?

AS568 200 Series covers dash 282 with a 0.139" (3.53 mm) cross section. Heavy machinery, large cylinders, process equipment

What extrusion gap is safe for this size?

For a 0.139" cross section, limit the diametral extrusion gap to 0.004–0.006" (0.10–0.15 mm) for pressures up to 150 bar. Above 150 bar, use a PTFE backup ring regardless of gap size.

What hardness should I specify?

70 Shore A is the standard for most static and dynamic applications up to 100 bar. Use 80 Shore A for 100–200 bar dynamic service. Use 90 Shore A only for extreme extrusion resistance or abrasive conditions.

What is the nearest ISO 3601 metric equivalent to AS568-282?

The closest ISO 3601 catalog size is 250.00x2.65 (ID 250.00 mm × CS 2.65 mm). ID differs by 155.26 mm — verify groove dimensions before substituting.

When do I need a backup ring?

Use a backup ring when pressure exceeds 1,500 psi (100 bar) or when the extrusion gap is larger than 0.15 mm for this cross section. PTFE backup rings are standard for AS568 sizes.

Related Resources

Imperial Size Chart

Browse the full AS568 table when you need adjacent dash numbers or series comparisons.

View AS568 chart

Size Converter

Convert this imperial size to metric equivalents before choosing ISO or JIS alternatives.

Open size converter

Compression Calculator

Check gland squeeze and confirm whether your groove depth matches the target compression range.

Calculate compression

AS568 PDF Download

Request the printable size chart for engineering review, quoting, or shop-floor reference.

Request AS568 PDF